Just How to Install a Bath Tub Yourself: Removing as well as Replacing.
Just How to Install a Bath Tub Yourself: Removing as well as Replacing.
Blog Article
Presented here in the next paragraph you can find a bunch of brilliant help and advice on the subject of How to Install a Bathtub Yourself.
Installing a bathtub isn't exactly brain surgery, yet it does call for strong plumbing, woodworking, and also sometimes, tiling skills. Replacing an old bathtub with a new one is also a moderately difficult project. If the old tub is easily easily accessible, the job can relocate immediately; if you need to open up a wall to eliminate the old tub and position the new bathtub, the job is a lot harder. In either situation, the project is within a home handyman's skills, although you will require an assistant to vacate the old bathtub as well as set in the new one. Make sure you have certified on your own for the task as well as are comfortable attempting it. Rather than working with a service provider to take control of a halfway-completed job, it is much better to think about employing one before you start. Possibilities are you may need a professional plumber to make tube links.
This post will help you mount a brand-new tub in your restroom if you have currently gotten a new tub and also do not need to change the setup of your previous water system pipes.
Your devices and also material checklist need to make up the following:
Removing Old Taps
If you require to change old taps with brand-new ones as a part of your setup, then the first thing you need to do is detach the water supply. After doing so, activate the taps to drain pipes any type of water remaining in the system. The procedure of removing the existing taps can be fairly troublesome due to the restricted accessibility that is commonly the case.
Make use of a basin wrench (crowsfoot spanner) or a faucet tool to reverse the nut that links the supply pipes to the faucets. Have a cloth prepared for the remaining water that will certainly come from the pipelines. Once the supply pipelines have been gotten rid of, use the very same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to quit the solitary taps from transforming during this procedure. Once the faucets have been eliminated, the holes in the bath/basin will certainly have to be cleansed of any old sealing substance.
Before going on to fit the new faucets, contrast the pipe links on the old taps to the brand-new faucets. If the old taps are longer than the brand-new taps, then a shank adapter is needed for the new faucets to fit.
Suitable New Taps
If the tails of the brand-new faucets are plastic, then you will certainly require a plastic port to stop damage to the thread. One end of the adapter fits on the plastic tail of the tap as well as the various other end provides a connection to the current supply pipes.
If you need to fit a monobloc, after that you will need minimizing couplers, which connects the 10mm pipe of the monobloc to the common 15mm supply pipe.
Next, place the faucet in the mounting hole in the bath/basin making sure that the washing machines are in place between the faucet and also the sink. Secure the tap in position with the supplier offered backnut. When the faucet is firmly in place, the supply pipes can be linked to the tails of the faucets. The faucets can either be connected by using corrugated copper piping or with typical faucet adapters. The former type ought to be linked to the faucet finishes first, tightening only by hand. The supply pipes can later on be attached to the various other end. Tighten both ends with a spanner after both ends have been connected.
Setting up the Tub
Making use of both wood boards under its feet, place the bathtub in the required setting. The wooden boards are practical in equally spreading out the weight of the bath tub over the area of the boards instead of focusing all the weight onto four small points.
The next goal is to make sure that the tub is leveled all round. This can be attained by examining the level and also readjusting the feet on the bath tub till the spirit level checks out level.
To set up taps, fit the bottom of the furthest versatile tap port to the suitable supply pipe by making a compression join; then do the same for the other tap.
Switch on the water supply and also examine all joints and also brand-new pipework for leakages as well as tighten them if needed. Fill up the tub and also check the overflow outlet and also the regular electrical outlet for leakages.
Lastly, repair the bath paneling as described in the manufacturer's instruction manual. Tiling and also securing around the tub ought to wait until the bathtub has actually been made use of a minimum of once as this will settle it right into its last setting.
Preparing for the Installation
To start with, the sustaining framework supplied with the bath needs to be fitted (if needed) according to the producer's instructions. Next off, fit the faucets or mixer to the tub. When fitting the faucet block, it is very important to make certain that if the tap features a plastic washing machine, it is fitted between the bath and also the taps. On a plastic bath, it is additionally practical to fit a supporting plate under the faucets system to prevent pressure on the tub.
Fit the adaptable faucet connectors to the bottom of both taps using 2 nuts and also olives (in some cases supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the outlet with the hole in the bath. Utilize the nut provided by the producer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the versatile overflow pipe to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bath. Make certain you use every one of the supplied washing machines.
Connect the trap to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Link all-time low of the overflow tube in a similar manner.The bathroom should now prepare to be fitted in its final placement.
Tiling Around the Bathtub
In the area where the bathroom meets the ceramic tile, it is essential to seal the joins with a silicone rubber caulking. This is necessary as the fitting can move sufficient to crack a stiff seal, creating the water to penetrate the wall in between the bathroom and the tiling, causing difficulties with dampness as well as feasible leakages to the ceiling below.
You can select from a range of coloured sealers to blend in your fixtures as well as installations. They are marketed in tubes and cartridges, as well as can securing voids up to a width of 3mm (1/8 inch). If you have a larger space to load, you can load it with twists of soaked newspaper or soft rope. Keep in mind to constantly load the bathtub with water before sealing, to enable the motion experienced when the bathtub remains in usage. The sealant can crack relatively early if you do not take into consideration this activity prior to securing.
Alternatively, ceramic coving or quadrant tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are additionally conveniently readily available on the marketplace. It is advisable to fit the tiles using water-resistant or waterproof sticky as well as grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Do you enjoy reading up on How to Install a Bathtub Yourself? Put a remark further down. We will be delighted to find out your opinion about this write-up. We are looking forward that you come back again later on. Remember to take a moment to distribute this blog entry if you appreciated it. Thanks a lot for going through it.
Estimate Report this page